Posted on Leave a comment

Overexposure Bug Fixed

MewPro Iliad’s overexposure problem in many video modes is fixed.

The Iliad source code at our GitHub repo has already been updated to the latest 1.2.15. Compiling and installation guide is here. Since this bug only affected sync signal parameters there is no need to update the firmware on your MewPro 2 boards.

All the video modes that the camera, GoPro Hero 4 Black or Silver can shoot are supported.

Enjoy!

Posted on Leave a comment

Migrating from Hero 3+ Black to Hero 4

An old genlock rig using MewPro 2 with Hero 3+ Black and Genlock Dongle can be upgraded to Hero 4. The post explains migrating from Hero 3+ Black to Hero 4.

Example Rig Migration

Suppose you have a 6-camera rig that consists of

  • 6 GoPro Hero 3+ Black cameras
  • 5 MewPro 2 boards
  • 1 GoPro Dual Hero
  • 1 Genlock Dongle

and these are connected in single dongle configuration:

Single Dongle Configuration for 6 Hero 3+ Blacks
Single Dongle Configuration for 6 Hero 3+ Blacks

Then the GoPro Dual Hero bacpac and the Genlock dongle are not necessary from now on. And now you’ll need one more MewPro 2 board and one MewPro Iliad as well as 6 Hero 4 (Black or Silver) cameras.

Remove the Dual Hero bacpac and the Dongle from your rig. Replace Hero 3+ Black to Hero 4. Burn the “MewPro4” software (https://github.com/orangkucing/MewPro4) to MewPro 2 boards.
migrate3bto4-inter

The connection to each MewPro 2 board is the same as in single dongle configuration, however, TRIG signal is not used for Hero 4. And since Hero 4 can be fed power from side USB or herobus and works without internal battery the spare wire previously used for TRIG can be reused to connect 3.3V power from Iliad to each MewPro 2 board.

Upgraded Rig

After connecting Iliad to MewPro 2 boards the upgraded sytem is like this:
migrate3bto4-after

Enjoy!

Posted on Leave a comment

Hero 4 Power Supply

In order to avoid camera’s overheat Hero 4 had better be fed with external five volt source and use without internal battery. This post enumerates ways of power supply in MewPro + Iliad system.

Note: If your cameras are located in rather remote places then please avoid ground loop. For good explanation on ground loop and its potential danger, common mode current see this article “What should I do to avoid accidental damage to the device?” written by an engineer of a famous USB logic analyser Saleae.

Ways of Power Supply

The following shows each component (camera, MewPro, and Iliad) is fed with, wiring MewPro board, and remarks.

(Warning: If all cameras and Iliad are powered by one big battery or one wall charger then please notice that there are ground loops. As ground loop itself is not harm, however, care should be taken to avoid accidental large common mode current. It is suggested that you’d better remove GND connection at each MewPro’s RJ45 connector in this case for getting around this.)

Power ON = auto” means a long press of the mode button at Iliad makes camera’s power on. Similarly, “Power OFF = auto” means off.

Power ON = manual” is a special case where we currently can’t power on using Iliad. We don’t know the reason why we can’t and it’s a shame, however, we gave up further experiment on the power method after several days of fruitless effort followed by nearly ruining/burning a Hero 4 Black by carelessly connecting a wrong power line. In this case we can power on cameras as in the following steps:

  1. Connect all cables and wires but power lines. Attach MewPro’s to cameras.
  2. Connect USB wallcharger or battery pack to Iliad (or DC 7-12V to Iliad’s barrel jack).
  3. Apply 5V to USB VBUS pin of MewPro 2 board.
  4. Power on each camera by manually long press camera’s mode button.
  5. Long press Iliad’s mode button

Power on this way also syncs all the settings stored in Iliad.

UPDATE 2 Dec 2016: A workaround is found for the last annoying case of “Power ON = manual“. By using a paper clip (see photo below) or scotch tape or something we can fix camera’s mode button to ON state.
_mg_2762-copy
Then the camera’s power can be controlled by applying 5V to USB VBUS pin. And once the camera powered on then Iliad can control everything of it. The trick is that button “press” is actually recognized by the camera when the button is “released” while “long press” is recognized by its pushed state.

Our recommended power supply method is the connection depicted in Table 2. If you order plug-n-play tailor made sets in our shop then we will use this wiring.

Legends

Table 1
MewPro 2 Iliad
GND GND
VSYNC VSYNC
HSYNC HSYNC
RESET RST
RXI TXO
Table 2
MewPro 2 Iliad
GND GND
VSYNC VSYNC
HSYNC HSYNC
RESET RST
RXI TXO
VCC 3V3
Table 3
MewPro 2 Iliad
GND GND
VSYNC VSYNC
HSYNC HSYNC
RESET RST
RXI TXO
VCC 3V3
USB VBUS *

*: USB VBUS as well as GND is connected to external 5V power supply. It must be “good” source as each camera requires 1A or less while recording.